Foundry Practice

From MeritBadgeDotOrg

(Difference between revisions)
Jump to: navigation, search
(New page: {{Infobox_MeritBadge_Red |name=Foundry Practice |image=Foundry.JPG |caption=Foundry Practice Merit Badge |subject= Discontinued Merit Badges |status= Discontinued |created= 1923 |disconti...)
Current revision (18:06, October 13, 2012) (edit) (undo)
(-expand)
 
(2 intermediate revisions not shown.)
Line 1: Line 1:
 +
{{DiscontinuedMeritBadge}}
 +
<br>
 +
{{Infobox_MeritBadge_Red
{{Infobox_MeritBadge_Red
|name=Foundry Practice
|name=Foundry Practice
|image=Foundry.JPG
|image=Foundry.JPG
-
|caption=Foundry Practice Merit Badge
 
-
|subject= Discontinued Merit Badges
 
-
|status= Discontinued
 
|created= 1923
|created= 1923
|discontinued= 1952
|discontinued= 1952
-
|requirements revision=n/a
+
|group= building
-
|pamphlet revision= n/a
+
|id = n/a
-
|field= Farming
+
|source1= Origin
-
|id= unavailable
+
|source2= new in 1923
 +
|replaced by= none
}}
}}
-
{{clear}}
+
<br>
-
{{ArticleMessageBox
+
<br>
-
|barcolor = #1e90ff
+
-
|width =
+
-
|left-indent = 5%
+
-
|image = StopHand.png
+
-
|text = Foundry Practice is a discontinued merit badge. Foundry Practice was first offered in 1923. It was discontinued in 1952.}}
+
-
== Merit badge requirements ==
+
<!-- ------------------------------------------------------ -->
 +
<!-- The text of the Requirements is on a locked subpage. -->
 +
<!-- Please offer comments or corrections -->
 +
<!-- under the Discussion tab at the top of this page. -->
 +
<!-- ------------------------------------------------------ -->
 +
{{reqs|at discontinuation|merit badge }}
 +
<br>
-
:1. (a) Make a freehand working drawing of a flask used for a bench moulding in the foundry; (b) describe same flask.
 
-
 
-
:2. (a) Show by section sketch a mould of a plate 12" long, 6" wide, 1" thick with gate and vents; (b) construct the mould.
 
-
 
-
:3. Make a perspective sketch of a pulley pattern 6" diameter, 2" face, the center to be cored 2" by use of core prints.
 
-
 
-
:4. Construct a wood pattern and core box as per the sketch outlined in Requirement 3; use shrinkage rule for the metal used, gray iron, bronze or brass. Change measurements to allow for finish all over casting and proper draft for removing pattern from mould.
 
-
 
-
:5. Describe how the cupola operates.
 
-
 
-
:6. (a) Describe a process for cleaning one of the above castings when removed from the mould; (b) clean one of the above castings.
 
-
 
-
:7. Describe the properties in sand that are best suited for foundry use and tell how to prepare sand for use.
 
-
 
-
:8. Tell what important safety precautions should be taken to protect the workers in a foundry - by the employer - by the employee.
 
-
 
-
Note: In each case when a mould is required the pattern must first be made.
 
-
 
-
 
-
 
-
{| style="margin: 0 0 0 10%; border-collapse: collapse; background: #F5F5F5; border: 1px solid #aaa; border-left: 10px solid blue;"
 
-
|-
 
-
| style="width: 52px; padding: 2px 0px 2px 0.5em; text-align: center;" | [[image:33215.jpg|45px|Boy Scout Requirements, ({{{1}}}) Edition]]
 
-
| style="padding: 0.25em 0.5em;" | '''The ''official'' source for the information shown in this article or section is:<br>[http://www.scouting.org/BoyScouts/AdvancementandAwards.aspx ''Handbook for Boys'', 1948 Edition''']
 
-
|}
 
== Notes ==
== Notes ==
 +
<br>
-
 
+
== See also ==
-
 
+
<br>
== External links ==
== External links ==
-
 
+
<br>
-
[[Category:Discontinued Merit Badges]]
+

Current revision

Foundry Practice merit badge has been discontinued. (See discontinued merit badges.)


Foundry Practice merit badge
Status: Discontinued BSA Advancement ID: n/a
Created: 1923 Origin: new in 1923
Discontinued: 1952 Replaced by: none

Contents




Foundry Practice merit badge requirements at discontinuation

  1. (a) Make a freehand working drawing of a flask used for a bench moulding in the foundry; (b) describe same flask.
  2. (a) Show by section sketch a mould of a plate 12" long, 6" wide, 1" thick with gate and vents; (b) construct the mould.
  3. Make a perspective sketch of a pulley pattern 6" diameter, 2" face, the center to be cored 2" by use of core prints.
  4. Construct a wood pattern and core box as per the sketch outlined in Requirement 3; use shrinkage rule for the metal used, gray iron, bronze or brass. Change measurements to allow for finish all over casting and proper draft for removing pattern from mould.
  5. Describe how the cupola operates.
  6. (a) Describe a process for cleaning one of the above castings when removed from the mould; (b) clean one of the above castings.
  7. Describe the properties in sand that are best suited for foundry use and tell how to prepare sand for use.
  8. Tell what important safety precautions should be taken to protect the workers in a foundry - by the employer - by the employee.

Note: In each case when a mould is required the pattern must first be made.


Boy Scout Requirements, ({{{1}}}) Edition The official source for the information shown in this article or section is:
Handbook for Boys, 1948 Edition

The text of these requirements is locked and can only be edited
by an administrator.
Please note any errors found in the above requirements on this article's Talk Page.


Notes


See also


External links


Personal tools
language