Pinewood Derby Tips

From MeritBadgeDotOrg

Jump to: navigation, search
Cub Scout Pinewood Derby Tips resources include Tips and Tricks to make your car fast.
Photos of winning Pinewood Derby car designs are included. Other resources include
the Pinewood Derby Official Rules, Overview, links, and key rules the BSA did not include.

Pinewood Tips
This page is also available as a printable pdf page.

Click photos below for close-ups
Blue Wedge - #1!
Blue Wedge - #1!
Gold Brick - Faster!Proved aerodynamics do not matter...
Gold Brick - Faster!
Proved aerodynamics do not matter...
Blue Brick - Record Holder
Blue Brick - Record Holder
Lead Brick Nano - Fastest Cub Scout Class
Lead Brick Nano - Fastest Cub Scout Class
Fan Car - Fastest Open Class All cars built and raced by Mark Lincoln.Photos used with permission.
Fan Car - Fastest Open Class
All cars built and raced by Mark Lincoln.
Photos used with permission.

These ideas come from a number of sources including: Cub Scout Grand Prix Pinewood Derby Guidebook #33721

Body Design

  1. Cars should be built by the Cub Scouts with some adult guidance. Make it fun!
  2. Measure twice, cut once. Start early and take your time. Scout Shops are happy to sell more cars.
  3. Help your Cub draw out his design on paper and then on the wood.
  4. The low wedge is a fast design. It is also easy to make. - See the Blue Wedge.
  5. A wide, flat front edge gets a better start off the starting pin and hits the end timer beam sooner.
  6. Aerodynamics is not a factor at 10 MPH. Weight, Axles, wheels, & lubrication are more important. - See the Gold Brick.
  7. Slick gloss paint reduces friction where the wheels rub the car body.

Axles and Wheels

  1. A longer wheelbase increases stability. Think of a dragster. Drill axle holes as far apart as allowed.
  2. Axles need a 90-degree angle so the car goes straight. Check angles with a square or protractor.
  3. Pre-drill your axle (nails) holes with a bit just under the size of the axle to prevent splintering.
  4. Lightly smooth wheel treads with fine sand paper to smooth tread. The treads must be left flat.
  5. After the car is painted, attach the wheels with a 1/32 to 1/16 inch gap. Don\'t glue the axles on yet.
  6. Some raise one front wheel slightly saying it reduces friction to have only 3 wheels touching the track.
  7. If your pack does not add rules requiring the use of the BSA axles (nails), buy professionally prepared axles on the internet.
  8. If your pack does not add rules regarding wheels, you can buy professionally prepared BSA wheels on the internet that are much faster.

Add Weight

  1. Weigh your car with wheels, axles, and any accessories (driver, steering wheel, etc.).
  2. Get your car as close to 5 ounces as possible.
  3. Keep the weight in the back to push the car down the ramp longer.
  4. The car may be hollowed out & weight inserted up to the 5 oz. maximum.
  5. You can also drill holes & insert fishing sinkers. Do not glue weights in yet.
  6. A precision 1/100-ounce digital scale is under $20. A ½ ounce resolution scale shows 4.8 to 5.2 oz as 5.0 oz!
  7. Ask to weigh your car on the official scale before check-in. It does not matter what your scale says.

Lubricate the Car

  1. Use a dry, fine powdered lubrication (graphite). Liquids or sprays can melt the wheels. Remember: graphite is messy.
  2. Shake wheels in baggy with graphite to coat the outside of the wheel first. - Look at the Blue Brick's wheel's are.
  3. Lube the wheel hole, axle, & axle head. Lube where the axle will touch the car. Use more graphite!
  4. Spin the wheels repeatedly on the axles to work in the graphite. You still didn't use enough graphite!
  5. Roll the car on a flat floor. It should travel in a straight line. If not, your axles may need to be trued to 90°


If your Pack does not prohibit motors, the only cars that will be able to win will be ones with motors. If your pack will not prohibit motors, you will need one too. Consider an airplane ducted electric fan from a hobby store, a nine-volt battery, and a switch. This is also the sure way to win Open Class events. - See the Fan Car.

Test the Car

  1. Now glue the axle only at the axle (nail) tip & attach wheel to car. Use epoxy or non-resin glue.
  2. Don't get any glue on the surface of the axle where the wheel rides. It can bind.
  3. Check your weight one last time and glue weights into place. Weights cannot be loose.
  4. Lube your wheels again immediately before the race. Bring lube with you to the race.
  5. Protect your car. Carry your car in a shoe box lined with tissue or other gentle padding.
  6. Do not play with the car until after the last race.
  7. Most important tip – make sure it is FUN!

See also

Best Design Best In Show Cubmaster's Pick Judge's Favorite Best Detail Best Paint Job
Most Colorful Most Original Most Realistic Most Aerodynamic Most Innovative Best Theme
Most Artistic Best Workmanship Most Decals Best Dragster Best Classic Design Most Futuristic
Best Scout Theme Best Truck Design Best Wedge Shape Most Creative Most Unique Most Patriotic
Personal tools