Signaling

From MeritBadgeDotOrg

Revision as of 19:28, October 7, 2012 by Scouterdennis (Talk | contribs)
Jump to: navigation, search
2010 Historic (a.k.a. "Centennial") Merit Badges "Data Entry" Deadline: With the deadline of December 31, 2010 for Scouts to earn the historical merit badges, the decision has been made to allow additional time thereafter for entering them into the ScoutNET system. The deadline for doing so has been set as March 31, 2011. This applies to those at the local council who enter advancement based on forms submitted, or unit management software file uploads provided. It also applies to unit advancement processors using Internet Advancement. The merit badges affected are: Carpentry, Pathfinding, Signaling, and Tracking. This is not intended as an extension of time to earn the badges; only as additional time for data entry. Troops can submit advancement reports for Historic Merit Badges earned by Scouts before 12/31/2010 through March 31, 2011. — Announcement from the National Council office.


Signaling "Centennial" merit badge
Status: Discontinued
Released: 1911, 2010 BSA Advancement ID:
Retired: 1992, 2010 Requirements Revision: 2010

Contents


The Signaling merit badge was one of the original 57 merit badges issued by the Boy Scouts of America in 1911. It replaced the 1910 Signaller "Badge of Merit".


Signaling requirements


1938 merit badge requirements

  1. Send and receive by Semaphore Code at the rate of not fewer than forty-eight letters per minute, or in the General Service (International Morse) Code, not fewer than twenty-four letters per minute.
  2. Send and receive signals by sound, using the buzzer, sounder, whistle, or bugle.
  3. Make an electric buzzer outfit, wireless outfit, blinker, or a heliograph outfit and send a message of not less than twenty-four letters with the same.

1945, 1950 merit badge requirements

  1. Make an electric buzzer outfit, wireless, blinker, or other signaling device.
  2. Send and receive in the International Morse Code, by buzzer or other sound device, a complete message of not less than 35 words, at a rate of not less than 35 letters per minute.
  3. Demonstrate an ability to send and receive a message in the International Morse Code by wigwag and by blinker or other light signaling device at a rate of not less than 20 letters per minute.
  4. Send and receive by Semaphore Code at the rate of not less than 30 letters per minute.
  5. Know the proper application of the International Morse Code and Semaphore Codes; when, where, and how they can be used to best advantage.
  6. Discuss briefly various other codes and methods of signaling which are in common use.


Boy Scout Requirements, ({{{1}}}) Edition The official source for the information shown in this article or section is:
Handbook for Boys, 1946 Edition

The text of these requirements is locked and can only be edited by an administrator.
Please note any errors found in the above requirements on this article's Talk Page.


Notes

Worksheet A FREE workbook for Signaling is available here! Adobe Acrobat PDF
with the maps, charts, links, diagrams, and checklists you need!
Or click here to print just the Signaling requirements. 		meritbadge.org has PDF and DOC versions of
Boy Scout merit badge workbooks,
Webelos workbooks, and Cub Scout workbooks.
  1. Per the BSA: "You should read the merit badge pamphlet on the subject." Pamphlets (books) are at local Scout Shops and online at ScoutStuff.org.
  2. "Get a signed Merit Badge application from your Scoutmaster." An online, printable Word doc file version is available.


Requirement resources

BSA Merit Badge Resources

2, 3, 5: Note: It's 35 letters per minute, not words per minute.

4: Flag semaphore signal schema Adobe Acrobat PDF (206K PDF) A diagram of flag semaphore signal actions and meanings in arm position order; action sequence required to send and receive a complete message; posing instructions for signaler. (Rev. 2, 3/10)

Related Ranks, Awards, and Merit Badges

2010 Historic merit badge program resources

Merit Badge MeritBadge.Org USScouts.Org Scouting.Org (BSA)
Carpentry Workbook Adobe Acrobat PDF Workbook Microsoft Word DOC document MB web page "2010" MB packet "Historical" MB pamphlet
Pathfinding Workbook Adobe Acrobat PDF Workbook Microsoft Word DOC document MB web page "2010" MB packet "Historical" MB pamphlet
Signaling Workbook Adobe Acrobat PDF Workbook Microsoft Word DOC document MB web page "2010" MB packet "Historical" MB pamphlet
Tracking Workbook Adobe Acrobat PDF Workbook Microsoft Word DOC document MB web page "2010" MB packet "Historical" MB pamphlet

The basics of the 2010 Historic Merit Badge Program include:

  • "The effective date for earning these new merit badges is April 1, 2010, and requirements must be completed no later than Dec. 31, 2010." — 2010 Historical MB Program
  • "The contemporary merit badges closely resemble the original designs of their counterparts with the exception of the border, which is gold." — 2010 Historical MB Program
  • The BSA Supply Division will not print (new) or re-print (old) pamphlets for these merit badges – official BSA materials for these merit badges will be available only in electronic format at Scouting.Org. (We have provided you those links, above).


History

1945, 1950 merit badge requirements

Historical Signaling merit badge.
Historical Signaling merit badge.
  1. Make an electric buzzer outfit, wireless, blinker, or other signaling device.
  2. Send and receive in the International Morse Code, by buzzer or other sound device, a complete message of not less than 35 words, at a rate of not less than 35 letters per minute.
  3. Demonstrate an ability to send and receive a message in the International Morse Code by wigwag and by blinker or other light signaling device at a rate of not less than 20 letters per minute.
  4. Send and receive by Semaphore Code at the rate of not less than 30 letters per minute.
  5. Know the proper application of the International Morse Code and Semaphore Codes; when, where, and how they can be used to best advantage.
  6. Discuss briefly various other codes and methods of signaling which are in common use.

1938 merit badge requirements

  1. Send and receive by Semaphore Code at the rate of not fewer than forty-eight letters per minute, or in the General Service (International Morse) Code, not fewer than twenty-four letters per minute.
  2. Send and receive signals by sound, using the buzzer, sounder, whistle, or bugle.
  3. Make an electric buzzer outfit, wireless outfit, blinker, or a heliograph outfit and send a message of not less than twenty-four letters with the same.

See also

Boy Scout portal
Varsity Scout portal
Venturing portal

Merit Badge information


External links


Retrieved from "http://meritbadge.org/wiki/index.php/Signaling"
Personal tools
language